P0743 Audi Code – Torque Converter Clutch Circuit Electrical

Possible Causes

Dirty transmission fluid
Low transmission fluid level
Faulty Torque Converter Clutch (TCC) Solenoid Valve
Torque Converter Clutch Solenoid Valve harness is open or shorted
Torque Converter Clutch Solenoid Valve circuit poor electrical connection

الأسباب المحتملة

القابض القابض لعزم الدوران ، سائل النقل القذرة ، سائل النقل ليفلويول ، محول ، ملول سائل ، محول الملف اللولبي ، محول الملف اللولبي ، أو مخابئ صمام ،

Possible Symptoms

Engine Light ON (or Service Engine Soon Warning Light)

الأعراض المحتملة

ضوء المحرك (أو خدمة محرك قريبا ضوء تحذير) ضوء)

Description

The Torque Converter Clutch (TCC) is designed to increase efficiency by mechanically coupling the engine to the transmission. The TCC solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter. The lock-up operation, however, is prohibited when A/T fluid temperature is too low. When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up. By performing a voltage drop test, the ECM detects that the Torque Converter Clutch (TCC) solenoid circuit is open or shorted and sets the Diagnostic Trouble Code (DTC).

الشرح

تم تصميم قابض محول عزم الدوران (TCC) لزيادة الكفاءة عن طريق اقتران المحرك ميكانيكيا إلى ناقل الحركة. يتم تنشيط صمام الملف اللولبي TCC ، مع الترس في D4 ، بواسطة وحدة التحكم في الإرسال (TCM) استجابة للإشارات المرسلة من سرعة السيارة ووحدة التحكم في المحرك (ECM). سيتم التحكم في عملية حبس المكبس. عندما يتم تنشيط صمام الملف اللولبي لمحول عزم الدوران ، فإن قابض قفل محول عزم الدوران سوف يشارك في إنشاء نسبة 1 إلى 1 دورة في الدقيقة بين عمود إدخال الإرسال والسرعة الدورانية لمحول عزم الدوران. ومع ذلك ، يتم حظر عملية القفل عندما تكون درجة حرارة السائل A/T منخفضة جدًا. عندما يتم الاكتئاب دواسة المسرع (أقل من 2/8) في حالة الإغلاق ، يجب ألا تتغير سرعة المحرك فجأة. إذا كان هناك قفزة كبيرة في سرعة المحرك ، فلا يوجد قفل. من خلال إجراء اختبار إسقاط الجهد ، يكتشف ECM أن دائرة الملف اللولبي لمحول عزم الدوران (TCC) مفتوحة أو مختصرة وتعيين رمز المتاعب التشخيصية (DTC).

Related Posts

Leave a Reply

Your email address will not be published.